GE Appliance Repair in Toronto & the GTA

We repair GE refrigerators, washers, dryers, wall ovens and dishwashers across Toronto and the GTA, including Profile, Café and Monogram lines. Parts are readily available and most faults are straightforward, so same-visit repairs are the norm. Service call $120 plus HST, 60-day parts and labour warranty.

GE appliances we service

  • Refrigerators
  • Washers
  • Dryers
  • Wall ovens
  • Dishwashers
— What we see most

Common GE problems

A GE bake element is one of the cheapest repairs in the kitchen and one of the most satisfying: the failure is usually visible as a burn mark, and the oven works properly the same hour.

  • 01

    HydroWave washer motor not engaging

  • 02

    Wall oven bake element burned through

  • 03

    Refrigerator door switch failing, light and cooling affected

  • 04

    Dishwasher door latch worn, cycle will not start

— Error codes

GE error codes and what to do

Half of these you can clear yourself in ten minutes. We would rather tell you that than book a visit you do not need.

  • F0Oven

    Stuck touchpad key

    DIY: clean the panel, cut power 5 min → then call us

  • F1Oven

    Control board failure

    Call us: board replacement

  • F2Oven

    Oven over-temperature

    Call us: stop using the oven

  • F3Oven

    Oven sensor open circuit

    Call us: sensor replacement

  • F4Oven

    Oven sensor shorted

    Call us: sensor replacement

  • F7Oven

    Touch panel or membrane fault

    Call us

  • dEDishwasher

    Door not detected as closed

    DIY: check the strike and hinge alignment

  • LOCOven

    Control lock engaged (not a fault)

    DIY: hold the lock key for 3 seconds to clear

— Parts

Why OEM parts matter on GE

GE oven sensors and elements are inexpensive genuine parts, so there is very little reason to fit anything else. Where OEM genuinely matters is the Monogram built-in line, whose control boards are series-specific and behave unpredictably when a near-match is substituted.

  • Factory parts on anything touching the control or sealed system
  • We tell you when an aftermarket part is genuinely fine and cheaper
  • Part numbers go on your invoice, so the next technician is not guessing

Job #4482 · Oven · Vaughan

Fixed
Model
PTD7000SNSS
Time on site
70 min
Parts
OEM
Total
$263 + HST
— Real repair

GE Wall Oven Not Heating in Maple

A GE wall oven in Maple stopped heating three days before a family dinner. The failure was visible the moment the panel came off, and so was the reason behind it.

Read the full work order
— Our work

GE appliances we have worked on

  • GE dishwasher repair in Toronto — built-in dishwasher under the counter with the lower kick plate removed and tools on the countertop

    GE dishwasher with the toe kick removed

  • GE washer repair in Toronto — stacked GE washer and dryer with the control console folded down, exposing the main board, wiring harness and inlet valves

    GE laundry centre with the console folded down

More of the same on our photo gallery.

— Pricing

Simple, honest pricing

  • Service call & diagnostic$120 + HSTCovers the visit and full diagnosis
  • Written quote on-siteBefore any workNothing proceeds until you approve it
  • Senior discount$50 offMention it when booking

What affects the repair price

  • The part itself — a door switch and a sealed-system component are different worlds.
  • Age and brand — luxury built-ins need factory-spec parts, and those cost more.
  • Access — a stacked unit in a condo closet takes longer to reach than a free-standing machine.

We do not publish repair price ranges. Senior Discount — $50 applies on top of the quoted job, and there are no trip surcharges or weekend premiums.

— FAQ

GE repair questions

My GE oven shows F3. What does that mean?

The oven temperature sensor circuit is open. It is one of the least expensive repairs in the kitchen — the part is cheap and the swap is quick. We confirm with a resistance reading rather than trusting the code, since a failing board can report the same thing.

My GE oven is dead but the clock works. What is wrong?

Usually one leg of the 240V supply has been lost at the breaker, which leaves the clock and lights working while nothing heats. It costs nothing to check and it is a genuinely common cause. If the supply is fine, the element or the board relay is next.

What is HydroWave and why does it fail?

It is GE’s belt-driven motor system on certain washers. The usual failure is the motor not engaging drive, which presents as a machine that fills and drains but never agitates or spins. It is a well-documented fault with available parts.

Do you repair GE Monogram built-ins?

Yes. Monogram refrigeration and wall ovens are built-in units fitted into cabinetry, so they need more time and factory-specific boards. We confirm parts availability before quoting rather than after.

— Near you

GE repair across the GTA

GE appliance acting up? We know these machines.

Call +1 (416) 885-0963or book online
— Related
Call NowBook Online
+1 (416) 885-0963